Willem programmer software version 0.97g or latest.
Verified chips on mentioned adapter are underlined. Details find in chip_test.xls file
Software may not support some chip, report problem in Willem/EZoFlash forums.

- Smart voltage Vcc=3.3/5V. Vpp=12V.
Jumpers Jp1, Jp3 (+5V), Jp5 (A18), Jp8 (Vpp=12V), Jp9 (sel.Vcc=5V) or
Jumpers Jp2 (Vcc=3.6V), Jp5 (A18), Jp8 (Vpp=12V)
Intel E28F016SA, E28F032SA Sharp LH28F016SAT
- Smart voltage Vcc=3.3/5V. Vpp=5/12V.
Jumpers Jp1, Jp3 (+5V), Jp5 (A18), Jp7 (Vpp=5V), Jp9 (sel.Vcc=5V) or
Jumpers Jp1, Jp3 (+5V), Jp5 (A18), Jp8 (Vpp=12V), Jp9 (sel.Vcc=5V) or
Jumpers Jp2 (+3.6V), Jp5 (A18), Jp8 (Vpp=12V)
Intel E28F016SV
- Vcc=3.3/5V. Vpp=5V. Jumpers Jp1, Jp3 (+5V), Jp5 (A18), Jp7 (Vpp=5V), Jp9 (sel.Vcc=5V)
Sharp LH28F400SU(H)T, LH28F800SU(H)T, LH28F016SU(H)T
- Vcc=5V. Vpp=5V. Jumpers Jp1, Jp3 (+5V), Jp5 (A18), Jp7 (Vpp=5V)
Intel TE28F160S5 Sharp LH28F160S5(H)T
- Vcc=2.7-3.6V. Vpp=3.3V. Jumpers Jp2 (+3.6V), Jp5 (A18), Jp7 (Vpp=3.6V)
Intel TE28F160S3 Sharp LH28F160S3(H)T
- Vcc=5V. Vpen=5V. Jumpers Jp1, Jp3 (+5V), Jp5 (A18), Jp7 (Vpp=5V)
Intel E28F320J5
- Vcc=2.7-3.6V. Vpen=3.3V . Jumpers Jp2 (+3.6V), Jp5 (A18), Jp7 (Vpp=3.6V)
Intel (TE,E) 28F320J3, 28F640J3, 28F128J3 Micron MT28F320J3, MT28F640J3, MT28F128J3
Sharp LH28F640SPHT, LH28F128SPHT ST Micro M58LW032D, M58LW064D (only extension D)


16Mb chips can be programmed on Willem SW 0.97g or latest version, selected device i28F016, i28F160-T, i28F160-B,LH28F160-T or LH28F160-B.

NEW !!
Highest density chips 28F320J3 and 28F640J3 are supported with latest SW versions 0.97d12c3 (ezoflash4v4) and 0.98d12c3 (ezoflash4v5).
Remove jumpers Jp10 and Jp9 at all. Restore lines to adapter connector BU7 pins 35 and 36.
Select device Flash 8/16bit (byte) > Intel > 28F320J3 (or 28F640J3).
Disable SW option: 28FxxxJ3 (Write to Buffer)!
Expect get ID response 0x89 Intel 0x89. Read, Erase, Blank check, Load file and Program.
Valid ID response can be verified with selected device LH28F160-B.

128Mb chip 28F128J3 can be programmed in 2 blocks.
Jumper Jp11 (A23) allow manage highest adress manually.
Source file split in 64Mb parts. Load 64Mb block, erase, blank check, program, verify on each block:
0-64Mb Jp11 on (A23-low). 64-128Mb Jp11 off (A23-high)