EZoFlash форум

hi ezo
please give schematic and pcb adapter tsop48d3 for 56pin flash same as s29gl128
and schematic and pcb adapter fbga64 a1
and with this adapter is possible read and write s29gl256 and s29gl512 ?

ezo please answer and give

see datasheet s29gl128
for 128 need A22
for 256 need A22 & A23
for 512 need A22 & A23 & A24
with adapter tsop48d3 and ezo4v5 is possible program s29gl256 and s29gl512 ????
please give schematic and pcb adapter tsop48d3 for s29gl128

please give schematic and pcb adapter tsop48d3 for s29gl128

You are in forum for long time. Why don't read / find existing resources , your visited even ?
http://www.ezoflash.com/adapters/tsop48d3/tsop48d3.htm
http://www.ezoflash.com/adapters/tsop48d3/tsop48d3.zip
viewtopic.php?f=9&t=4569
http://www.ezoflash.com/adapters/tsop48 ... _guide.pdf
You have to read/write 128 Mb chip in 32Mb parts , manage parts manually with jumpers A21(JpF), A22 (JpH).

with adapter tsop48d3 and ezo4v5 is possible program s29gl256 and s29gl512 ????

Find tsop48d3 schematic, spansion chip datasheet with tsop56 layout.
Adapter has extended pin out from tsop48 pads area, connected to R7 and JpH. For tsop56 chip it is pin 2 (A22). You have to create new equal connections with resistors and jumpers to tsop56 pins 1 (A23), 56 (A24)
S29GL512 read/write in 16 parts of 32Mb, parts switch managed by 4 jumpers - JpF, JpH and 2 new ones.
Same idea applied in adapter fbga64a1, 4 jumpers allow tricky programming chips up 512Gb (S29GL512N), one spare jumper for driving of A25 (1Gb).

schematic and pcb adapter fbga64 a1

schematic not created , pcb and component layout
http://www.ezoflash.com/adapters/fbga64a1/fbga64a1.zip

You have to create new equal connections with resistors and jumpers to tsop56 pins 1 (A23), 56 (A24)
S29GL512 read/write in 16 parts of 32Mb, parts switch managed by 4 jumpers - JpF, JpH and 2 new ones.
Same idea applied in adapter fbga64a1, 4 jumpers allow tricky programming chips up 512Gb (S29GL512N), one spare jumper for driving of A25 (1Gb).

if possible you add for me this 3 new jumper for s29gl256 to 1Gb and giveme schematic
why not have schematic for adapter ?
this schematic is manual ?

ezo please helpme
and giveme schematic
thancks

hi ezo
i need read and write s29gl256
if i add 1 resistor in a23 for new jumper i can read and write this chip
i must add 2k2 resistor ?
i connect 1pin resistor to vcc and other pin to jumper ?
and other pin jumper to gnd ?
you make new pcb and schematic for tsop56 flash with add new jumper ?
i see s29gl256 schematic this flash have 3 pin RFU i must connect this pin or not ?
pin29 is Vio i must connect this pin or not ?

Yes add extra resistor 2k2 and jumper to pin 1 (A23).
Use equal reference in tsop48d3 schematic - R7 , jumper H to pin2 (A22).
Note , tsop48d3 has 48 pin layout + extra pins for 56 pin package, incl. pin29 Vio

you make new pcb and schematic for tsop56 flash with add new jumper ?

Apply same board. Solder single thin wire to chip pin 1 (or pin1 contactpad on comercial tsop48d3). Connect this wire to ground (A23-0) for 0-128Mb, connect to pull-up resistor for 128-256 Mbit.
Find S29GL128 guide in my forum. Note, 8 blocks x32Mbit.

see s29gl256 schematic this flash have 3 pin RFU i must connect this pin or not ?

Can't find. tsop56/pin3 - A15

for s29gl256 i must how set jumper ?
please giveme jumper setting

ezo please helpme
i need how set jumper setting for s29gl256
i make pcb and waiting your answer for how set new jumper for read and write 8 part flash

Do you read S29GL128 programming guide from my resources. All settings described step by step including initial jumpers- step2 in doc.
Extra pin 1 (A23) initially is grounded.
Is chip correct soldered ? In tsop48d3 docs you find 48 central contactpads , for tsop56 chip find extra contactpads for tsop56 pins 1 and 2, pin 29.
Check all solderings. You have to get same ID from Willem SW described in guide.

i read S29GL128 programming guide
my id is correct
i need how set jumper for read and write s29gl256 in 8 part
i connect pin1 and 2 (pin1=A22 & pin2=A23) but not know connect pin29 to how pin
my id check this info :
manufacture id : 0001 AMD
device code : 227E
i will know this two question
1: i must connect pin29 s29gl256 to how pin adapter ?
2: you sure with software extID_erase16.exe this chip erase complete ? i erase this chip but when blank check is not empty
3: FOR ERASE THIS CHIP I MUST SET JUMPER JPF,JPH,AND NEW JPI ?
4:how i can use new jumper for A23
Set adapter jumpers JpF (A21- log.0), JpH (A22-log.0), memory area 0-32Mb.
Remove jumper JpF (A21- log.1), set JpH (A22-log.0), memory area 32-64Mb.
Set jumper JpF (A21- log.0), remove JpH (A22-log.1), memory area 64-96Mb.
Remove jumpers JpF (A21- log.1) and JpH (A22-log.1), memory area 96-128Mb.
and for 4part
128-160
160-192
192-224
224-256
i do not know how use jumper for 128 to 256mb
please helpme about this question

tsop56 with s29gl256 adapter

1: i must connect pin29 s29gl256 to how pin adapter ?

I supposed tsop48d3 usage, where pad and connection OK.
Why do not look to tsop48d3 schematic or chip datasheet ? Vio is output buffer power and pin 29 should be tied to Vcc (2.7..3.6).

2: you sure with software extID_erase16.exe this chip erase complete ? i erase this chip but when blank check is not empty

No problems found until now. Set programmer in pcb3b mode ! Other settings are same. What ID return my utility ?

3: FOR ERASE THIS CHIP I MUST SET JUMPER JPF,JPH,AND NEW JPI ?

Yes, all manual highest adress are log.0 . Note, entire chip will be erased.

4:how i can use new jumper for A23

A23 - log0, pin grounded for memory 0-128Mb
A23- log1 , pin to Vcc pull-up resistor 128-256
start again
Set adapter jumpers JpF (A21- log.0), JpH (A22-log.0), memory area 128-160Mb, ....

i think software extID_erase16 can not erase s29gl256 or willem software can not program i try for erase this chip . chip erase but not blank