28F128J3C 28F128J3A 28F256J3C read and write

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am
28F128J3C 28F128J3A 28F256J3C read and write

Сообщение Albert-M » Сб май 19, 2012 6:34 pm

BIG THX TO EZO!!
only now had time to make the fbga64b1adapter , work ok and with this flash tested
28F128J3C
28F128J3A
28F256J3C
Вложения
2013-02-16 01.06.36.jpg
2013-02-16 01.06.36.jpg (52.65КБ)20330 просмотров
2013-02-16 01.04.37.jpg
2013-02-16 01.04.37.jpg (117.48КБ)20330 просмотров
Последний раз редактировалось Albert-M Пт фев 15, 2013 11:18 pm, всего редактировалось 1 раз.

Ezo
------
Сообщения:2041
Зарегистрирован:Пн янв 03, 2005 6:50 pm
Откуда:Riga

Re: TE28F128J3C read and write

Сообщение Ezo » Сб май 19, 2012 8:35 pm

Do you apply tsop56a1 ?
Note fbga64a1 is 29LVxxx/GLxx compatible only.
28F128J3 in same fbga package (64 pin , 1mm pitch ) has another pin layout.
28F128J3 cannot be programmed with fbga64a1

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: TE28F128J3C read and write

Сообщение Albert-M » Сб май 19, 2012 9:08 pm

tsop56a1 i use i maked adapter for bga flash , only my problem how to read and write corectly
in 8x16mb part or 4x32mb part ?
i need correct jumper settings
pls help me EZO

Ezo
------
Сообщения:2041
Зарегистрирован:Пн янв 03, 2005 6:50 pm
Откуда:Riga

Re: TE28F128J3C read and write

Сообщение Ezo » Вс май 20, 2012 12:26 pm

Latest SW 0.98d12c3/0.97d12c3 have 28F640J3 support in 8bit mode.
In adapter tsop56a1 restore lines from BU7/35 and BU7/36. Connected jumpers Jp9 and Jp10 are removed , don't use.
1) Adapter tsop56a1, set jumper Jp11 (A23-log0)
SW 0.98d12c3, selected chip Flash 28Fxxx > 28Fx00 8/16bit > LH28F160-B (selection for ID only)
Action Get ID . Expect reply 0x89 Intel, 0x18 28F128J3 . Attention here to 0x18. Chip name was wrong in previous SW versions, should be fixed now.
2) SW 0.98d12c3, selected chip 3.3V adapter > Flash 8/16bit(byte)> Intel > 28F640J3
Untick/disable SW option 28FxxxJ3 (write to buffer).
Read chip. Save first 0-64Mb part. Remove jumper Jp11 (A23-log1). Read chip. Save second 64-128Mb part. Merge files 0-128Mb (16MB).
3) Erase/program chip. Split source 128Mb in 2 parts.
Set jumper Jp11 (A23-log0). Erase chip. Blank check. Load first part. Program/verify.
Remove jumper Jp11 (A23-log1). Erase chip. Blank check. Load second part. Program/verify.
No attention to Get ID , have reply 0x89 Intel , 0x89 .
------------
For equal fbga design apply tsop56 schematic, without r1,r2,jp9,jp10. Direct connect A21 and A22. Jp11/R3 connect to ball G1 (A23 128M). Apply extra resistor/jumper for 256Mb chip, connect to ball H8 (A24), read/write in 4 parts.

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: TE28F128J3C read and write

Сообщение Albert-M » Вс май 20, 2012 6:08 pm

thank u , the 128 mb only on 2 part .. wery nice info . thank u EZO :wink:

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: TE28F128J3C read and write

Сообщение Albert-M » Вс май 20, 2012 7:20 pm

Ezo писал(а):Latest SW 0.98d12c3/0.97d12c3 have 28F640J3 support in 8bit mode.
In adapter tsop56a1 restore lines from BU7/35 and BU7/36. Connected jumpers Jp9 and Jp10 are removed , don't use.
1) Adapter tsop56a1, set jumper Jp11 (A23-log0)
SW 0.98d12c3, selected chip Flash 28Fxxx > 28Fx00 8/16bit > LH28F160-B (selection for ID only)
Action Get ID . Expect reply 0x89 Intel, 0x18 28F128J3 . Attention here to 0x18. Chip name was wrong in previous SW versions, should be fixed now.
2) SW 0.98d12c3, selected chip 3.3V adapter > Flash 8/16bit(byte)> Intel > 28F640J3
Untick/disable SW option 28FxxxJ3 (write to buffer).
Read chip. Save first 0-64Mb part. Remove jumper Jp11 (A23-log1). Read chip. Save second 64-128Mb part. Merge files 0-128Mb (16MB).
3) Erase/program chip. Split source 128Mb in 2 parts.
Set jumper Jp11 (A23-log0). Erase chip. Blank check. Load first part. Program/verify.
Remove jumper Jp11 (A23-log1). Erase chip. Blank check. Load second part. Program/verify.
No attention to Get ID , have reply 0x89 Intel , 0x89 .
------------
For equal fbga design apply tsop56 schematic, without r1,r2,jp9,jp10. Direct connect A21 and A22. Jp11/R3 connect to ball G1 (A23 128M). Apply extra resistor/jumper for 256Mb chip, connect to ball H8 (A24), read/write in 4 parts.
i have one question , my home made adapter maked with very small wires , this is not good solution .. but work , possible to make for me one adapter converter tshop56-a1 to fbga64 UP adapter? pcb layout .
pls help me .

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: TE28F128J3C read and write

Сообщение Albert-M » Вс май 20, 2012 7:43 pm

how i can erase chip?
Vpp Range error

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: TE28F128J3C read and write

Сообщение Albert-M » Вс май 20, 2012 7:52 pm

Albert-M писал(а):how i can erase chip?
Vpp Range error
problem sloved missing JP7 jumper:)

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: TE28F128J3C read and write

Сообщение Albert-M » Пн май 21, 2012 8:02 pm

hy not find fbga design adapter ? possible to make ? pcb to ezo - fbga64 adapter applied with 256mb support

Ezo
------
Сообщения:2041
Зарегистрирован:Пн янв 03, 2005 6:50 pm
Откуда:Riga

Re: TE28F128J3C read and write

Сообщение Ezo » Чт май 31, 2012 9:24 pm

possible to make ?
Unfortunately busy time now.

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: 28F128J3C 28F128J3A 28F256J3C read and write

Сообщение Albert-M » Пт фев 15, 2013 11:22 pm

:wink:
up .

Ezo
------
Сообщения:2041
Зарегистрирован:Пн янв 03, 2005 6:50 pm
Откуда:Riga

Re: 28F128J3C 28F128J3A 28F256J3C read and write

Сообщение Ezo » Сб фев 16, 2013 8:59 am

You have got documents for testing and approval in November 2012.
Not working ? Any other problems ?
Вложения
fbga64b1.zip
(33.08КБ)683 скачивания

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: 28F128J3C 28F128J3A 28F256J3C read and write

Сообщение Albert-M » Сб фев 16, 2013 10:05 am

Ezo писал(а):You have got documents for testing and approval in November 2012.
Not working ? Any other problems ?
The adapter working , now is under test :)

Albert-M
Сообщения:74
Зарегистрирован:Пт дек 16, 2011 7:15 am

Re: 28F128J3C 28F128J3A 28F256J3C read and write

Сообщение Albert-M » Вс фев 17, 2013 3:49 pm

Problem with 28F256J3C Block Erase Error
Вложения
28f2561.JPG
28f2561.JPG (71.04КБ)20294 просмотра
28f256.JPG
28f256.JPG (63.53КБ)20297 просмотров

Ezo
------
Сообщения:2041
Зарегистрирован:Пн янв 03, 2005 6:50 pm
Откуда:Riga

Re: 28F128J3C 28F128J3A 28F256J3C read and write

Сообщение Ezo » Пн фев 18, 2013 12:29 am

0x89 Intel 0x1D
- correct device ID for 28F256J3 :-)
Problem with 28F256J3C Block Erase Error
Try http://www.ezoflash.com/downloads/software/28FxxxJx.zip
Programmer in Jp97mode. Read doc.

Ответить